User Tools

Site Tools


software:yg_9.11.3_to_9.11.4

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

software:yg_9.11.3_to_9.11.4 [2013/10/02 01:56]
Jim Lovell created
software:yg_9.11.3_to_9.11.4 [2013/10/02 02:02] (current)
Jim Lovell
Line 80: Line 80:
  
 6. as root 6. as root
-cd /​usr2/​eremotectrl+cd /​usr2/​eremotectrl/make
 make clean make clean
 make build make build
Line 86: Line 86:
  
 7. reboot 7. reboot
- 
-8. Log in as oper 
-cd /​usr2/​control 
- 
-added the following to skedf.ctl: 
- 
-* DBBC target values for IF counts in set-up procedure, up to 4 
-* values for up to four IFs, in order, this will cause an error 
-* in IFx=... command execution if used for DBBC DDC versions 
-* before v101 
-* default is nulls if not present 
-dbbc_if_targets ​ 25000 25000 35000 35000 
-*-------------------------------------------------------------- 
-* DBBC BBC TPI target levels 
-* has no effect for DDC versions before v103 
-* default is null if not present 
-dbbc_bbc_target 16000 
- 
-cd /usr2/proc 
-modified station.prc as follows: 
-     (F) This step is only for stations with DBBCs that are updating 
-         from previous version of 9.11.x, x=0, 1, or 2. Three changes 
-         are needed to the station.prc library: 
- 
-         ​(i) ​  ​Please insert the command "​bbc_gain=all,​agc"​ at the end 
-               of your SETUPA procedure. ​ This command is a "​no-op"​ 
-               for DDC version less than v103, but including it is 
-               ​recommended that be added for future backward 
-               ​compatibility. ​ For stations with v104 or higher, as 
-               ​additional parameter specifying the target count level 
-               can be added if it is desired, e.g., 
-               "​bbc_gain=all,​agc,​16000"​ 
- 
-         ​(ii) ​ Add the procedure "​BBC_LEVEL"​ to your station.prc 
-               ​library. ​ This can probably done most easily with the 
-               ​following commands: 
- 
-                 cd /usr2/proc 
-                 cp /​usr2/​fs/​st.default/​proc/​bbc_level.prc . 
-                 pfmed 
-                   ​st,​bbc_level::​bbc_level,​bbc_level 
-                   ex 
-                 rm bbc_level.prc 
- 
-         (iii) This step is only for stations with non-continuous cal and has 
-               two parts. 
- 
-               (a) Edit the CALTSYS_MAN procedure and insert the command 
-                   "​bbc_gain=all,​man"​ right after the "​IFMAN"​ command. 
- 
-               (b) Edit the CALTSYS procedure and insert the command 
-                   "​bbc_gain=all,​agc"​ right after the "​IFAGC"​ command. 
- 
  
 </​code>​ </​code>​
/home/www/auscope/opswiki/data/pages/software/yg_9.11.3_to_9.11.4.txt · Last modified: 2013/10/02 02:02 by Jim Lovell